![]() If I have any complaint about these CGS suppressors, it’s the additional 0.8 inches of length that’s brought to the table by the thread adapters. It’s the same size as the wrench flats on the base of the Hyperion and Hyperion K. Near the base of the thread adapter is a neat looking wrench flat feature that will accept a deep socket, box wrench, adjustable wrench, or possibly even 12-point wrench. Not that Hyperion owners are likely to ever shoot unsuppressed. In fact, given their diminutive size they work better as stand-alone muzzle compensators than you’d probably expect. The thread adapters also include a small compensator that diffuses gases even more rapidly upon entering the Hyperion. Available in both 5/8×24 and 1/2×38, the thread adapters effectively convert your square-shouldered muzzle into a taper-shouldered muzzle, throwing the required 5/8×24 threads out in front of the taper. On most barrels with a standard, square shoulder, you will likely want to run CGS’ new Hyperion Thread Adapter. That taper will provide a fantastic, full gas seal along with massively increased mating surface area, which does wonders to help prevent the suppressor from coming loose during use. If you’re installing a Hyperion on your SIG SAUER ( creators of the 25-degree tapered shoulder) or a firearm that borrowed the SIG taper design, go ahead and thread the suppressor directly onto the barrel. for TTAGīoth of the new Hyperions employ a 25-degree taper section before the mounting threads. Left raw, the layer-by-layer process is visible if you look closely enough e specially on angled surfaces (see below). for TTAGīelieve it or not, what you end up with is a truly monolithic end product that actually has a more consistent, finer metal grain structure with fewer (like, zero) metallurgic imperfections than you find inside a forged or cast product, or a product that’s machined from a billet / forging or casting. Unsintered Ti dust can be blown out as needed during the build process in order to prevent it from becoming trapped inside internal structures. Then another layer of dust, another pass of the laser, and repeat until your end product is built one teeny micro-fraction-of-an-inch layer at a time. The “3D printing” process involves depositing a fine layer of Ti dust then using a powerful laser to sinter, or melt/fuse/weld, this new layer to the previous layer in only the precisely desired places. 30 caliber Hyperions is made entirely of DMLS titanium. Upgraded and quieter than ever, the new CGS Hyperion and Hyperion K have just hit the market, and we went hands-on. Now, with the advent of metal 3D printing (called DMLS, or direct metal laser sintering), CGS has been untethered to create internal geometries that are impossible to machine. 30 cal sound suppression prowess for years thanks to its unique, patented internal structure. It has been coated on the exterior with PVD Black DLC and the internal surfaces have been coated with SX Line or Hexagonal Boron Nitride.ĭesigned and manufactured in Artesia, New Mexico USA by CGS Suppressors LLC, a division of CGS Group LLC.The CGS Group Hyperion has lead the industry in. The HELIOS QD Ti, just like all CGS Suppressors, has a lifetime warranty. The HELIOS QD Ti is full auto rated with a 10″ minimum barrel length restriction for 5.56mm and will handle larger calibers up to and including 300 Norma Magnum. All tertiary components of the HELIOS QD Ti Kit are also manufactured from Grade V Titanium. A ported front cap is included to ensure blowback mitigation for left hand shooters or for use with calibers or weapon systems that may be prone to over-gassing. A sealed front cap is provided for the maximum sound reduction possible. The interchangeable rear caps are complimented with interchangeable front caps as well. The HELIOS QD Ti comes with a 1/2×28 threaded rear cap, a 5/8×24 threaded rear cap, and an adapter ring threaded in 1.375×24 to accept a plethora of industry QD mounting solutions. 36 bore significantly reduces back pressure and muzzle flash while also allowing the suppressor to be used with multiple calibers. The HELIOS QD Ti system was designed to be extremely versatile. ![]() The HELIOS QD Ti utilizes a full DMLS Grade V Titanium construction for maximum strength, light weight, and extreme durability. By using a taper interface between the muzzle device and the signature suppressor, we ensure the muzzle device threads will not carbon lock. This unique design allows for peak sound reduction for its size and elimination of the flash signature as well as consistent, minimal and repeatable point of impact shift. The patented “Varying Core Diameter” technology unique to CGS Suppressors is unlike anything the firearms industry has ever seen before. The CGS HELIOS QD Ti is a short, quick attach rifle silencer designed specifically for 5.56mm rifles and carbines. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |